• Ex. VAT 
  •  Inc. VAT

Fischer FNAII Stainless Nail Anchor with Nail Head

Item No. 00600110

Length

  • 40mm
  • 65mm
  • 85mm
[Length::40mm]

Description

Plain

The fischer nail anchor FNA II 6 with nail head is made of stainless steel. The FNA II is set in a time-saving manner in the push-through installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II 6 with nail head is suitable for fixing mounting rails and timber or sub-constructions in external areas.

Advantages

  • The special active principle allows for a simple hammerset installation and, therefore, a short processing time.
  • The extremely short anchor depth prevents reinforcement hits, and creates the conditions for a trouble-free installation.
  • The optimised expansion clip ensures hold when placing in the drill hole, and prevents it falling out during overhead installations.
  • The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety.
  • A range of head shapes allows for the fixing of wide-ranging fixtures, and for the ideal adaptation to suit the intended use.

Threaded

The fischer nail anchor FNA II 6 with thread and flange nut is made of stainless steel. The FNA II is set in a time-saving manner in the push-through or pre-positioned installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II with thread and flange nut is suitable for fixing metal clamps for conduits and pipes in outdoor areas.

Advantages

  • Easy removal of fire protection board without damage
  • Reusability of fire protection board
  • Safe anchorage, particularly when exposed to vibration, wind, and pushing/pulling influences
  • Low anchoring depth (30 mm)
  • Convenient installation without torque-controlled setting tool
  • Approved system that has proven itself one million times over

Plain

The fischer nail anchor FNA II 6 with nail head is made of stainless steel. The FNA II is set in a time-saving manner in the push-through installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II 6 with nail head is suitable for fixing mounting rails and timber or sub-constructions in external areas.

Advantages

  • The special active principle allows for a simple hammerset installation and, therefore, a short processing time.
  • The extremely short anchor depth prevents reinforcement hits, and creates the conditions for a trouble-free installation.
  • The optimised expansion clip ensures hold when placing in the drill hole, and prevents it falling out during overhead installations.
  • The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety.
  • A range of head shapes allows for the fixing of wide-ranging fixtures, and for the ideal adaptation to suit the intended use.

 

Plain

The fischer nail anchor FNA II 6 with nail head is made of stainless steel. The FNA II is set in a time-saving manner in the push-through installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II 6 with nail head is suitable for fixing mounting rails and timber or sub-constructions in external areas.

Advantages

  • The special active principle allows for a simple hammerset installation and, therefore, a short processing time.
  • The extremely short anchor depth prevents reinforcement hits, and creates the conditions for a trouble-free installation.
  • The optimised expansion clip ensures hold when placing in the drill hole, and prevents it falling out during overhead installations.
  • The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety.
  • A range of head shapes allows for the fixing of wide-ranging fixtures, and for the ideal adaptation to suit the intended use.

 

Cookie Policy

We use cookies to remember your settings, personalise content, improve website performance, analyse traffic and assist with our general marketing efforts. Learn more